Sync the devicetrees with Linux and adjust the board names.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
imx6ul-phytec-segin-ff-rdk-nand.dtb \
imx6ul-pico-hobbit.dtb \
imx6ul-pico-pi.dtb \
- imx6ul-kontron-n631x-s.dtb \
- imx6ull-kontron-n641x-s.dtb
+ imx6ul-kontron-bl.dtb \
+ imx6ull-kontron-bl.dtb
dtb-$(CONFIG_MX6ULL) += \
imx6ull-14x14-evk.dtb \
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx6ul-kontron-bl.dts"
+
+/ {
+ model = "Kontron BL i.MX6UL 43 (N631X S 43)";
+ compatible = "kontron,bl-imx6ul-43", "kontron,bl-imx6ul",
+ "kontron,sl-imx6ul", "fsl,imx6ul";
+
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm7 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ status = "okay";
+ };
+};
+
+&i2c4 {
+ touchscreen@5d {
+ compatible = "goodix,gt928";
+ reg = <0x5d>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_cap_touch>;
+ interrupt-parent = <&gpio5>;
+ interrupts = <6 IRQ_TYPE_LEVEL_LOW>;
+ reset-gpios = <&gpio5 8 GPIO_ACTIVE_HIGH>;
+ irq-gpios = <&gpio5 6 GPIO_ACTIVE_HIGH>;
+ };
+};
+
+&lcdif {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_lcdif_dat &pinctrl_lcdif_ctrl>;
+ /* Leave status disabled because of missing display panel node */
+};
+
+&pwm7 {
+ #pwm-cells = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm7>;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl_cap_touch: captouchgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER6__GPIO5_IO06 0x1b0b0 /* Touch Interrupt */
+ MX6UL_PAD_SNVS_TAMPER7__GPIO5_IO07 0x1b0b0 /* Touch Reset */
+ MX6UL_PAD_SNVS_TAMPER8__GPIO5_IO08 0x1b0b0 /* Touch Wake */
+ >;
+ };
+
+ pinctrl_lcdif_ctrl: lcdifctrlgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_CLK__LCDIF_CLK 0x79
+ MX6UL_PAD_LCD_ENABLE__LCDIF_ENABLE 0x79
+ MX6UL_PAD_LCD_HSYNC__LCDIF_HSYNC 0x79
+ MX6UL_PAD_LCD_VSYNC__LCDIF_VSYNC 0x79
+ MX6UL_PAD_LCD_RESET__LCDIF_RESET 0x79
+ >;
+ };
+
+ pinctrl_lcdif_dat: lcdifdatgrp {
+ fsl,pins = <
+ MX6UL_PAD_LCD_DATA00__LCDIF_DATA00 0x79
+ MX6UL_PAD_LCD_DATA01__LCDIF_DATA01 0x79
+ MX6UL_PAD_LCD_DATA02__LCDIF_DATA02 0x79
+ MX6UL_PAD_LCD_DATA03__LCDIF_DATA03 0x79
+ MX6UL_PAD_LCD_DATA04__LCDIF_DATA04 0x79
+ MX6UL_PAD_LCD_DATA05__LCDIF_DATA05 0x79
+ MX6UL_PAD_LCD_DATA06__LCDIF_DATA06 0x79
+ MX6UL_PAD_LCD_DATA07__LCDIF_DATA07 0x79
+ MX6UL_PAD_LCD_DATA08__LCDIF_DATA08 0x79
+ MX6UL_PAD_LCD_DATA09__LCDIF_DATA09 0x79
+ MX6UL_PAD_LCD_DATA10__LCDIF_DATA10 0x79
+ MX6UL_PAD_LCD_DATA11__LCDIF_DATA11 0x79
+ MX6UL_PAD_LCD_DATA12__LCDIF_DATA12 0x79
+ MX6UL_PAD_LCD_DATA13__LCDIF_DATA13 0x79
+ MX6UL_PAD_LCD_DATA14__LCDIF_DATA14 0x79
+ MX6UL_PAD_LCD_DATA15__LCDIF_DATA15 0x79
+ MX6UL_PAD_LCD_DATA16__LCDIF_DATA16 0x79
+ MX6UL_PAD_LCD_DATA17__LCDIF_DATA17 0x79
+ MX6UL_PAD_LCD_DATA18__LCDIF_DATA18 0x79
+ MX6UL_PAD_LCD_DATA19__LCDIF_DATA19 0x79
+ MX6UL_PAD_LCD_DATA20__LCDIF_DATA20 0x79
+ MX6UL_PAD_LCD_DATA21__LCDIF_DATA21 0x79
+ MX6UL_PAD_LCD_DATA22__LCDIF_DATA22 0x79
+ MX6UL_PAD_LCD_DATA23__LCDIF_DATA23 0x79
+ >;
+ };
+
+ pinctrl_pwm7: pwm7grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_VSYNC__PWM7_OUT 0x110b0
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#if defined(CONFIG_FIT)
+
+/ {
+ binman: binman {
+ filename = "flash.bin";
+ pad-byte = <0x00>;
+
+ spl: blob-ext@1 {
+ offset = <0x0>;
+ filename = "SPL";
+ };
+
+ uboot: blob-ext@2 {
+ offset = <0x11000>;
+ filename = "u-boot.img";
+ };
+ };
+};
+
+#endif /* CONFIG_FIT */
+
+/*
+ * To make the PHYs work, we need to set the reset pin once. Afterwards
+ * in Linux we can't assign the shared reset GPIO to the PHYs, as this
+ * would cause Linux to reset both PHYs every time one of them gets
+ * reinitialized.
+ *
+ * Also we disable the second ethernet as it currently doesn't work with
+ * the devicetree setup in U-Boot.
+ */
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ phy-reset-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ micrel,led-mode = <0>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&fec2 {
+ status = "disabled";
+ /delete-property/ phy-handle;
+ /delete-node/ mdio;
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ gpio-leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_leds>;
+
+ led1 {
+ label = "debug-led1";
+ gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ linux,default-trigger = "heartbeat";
+ };
+
+ led2 {
+ label = "debug-led2";
+ gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+
+ led3 {
+ label = "debug-led3";
+ gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
+ default-state = "off";
+ };
+ };
+
+ pwm-beeper {
+ compatible = "pwm-beeper";
+ pwms = <&pwm8 0 5000>;
+ };
+
+ reg_3v3: regulator-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ reg_5v: regulator-5v {
+ compatible = "regulator-fixed";
+ regulator-name = "5v";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_otg1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ reg_vref_adc: regulator-vref-adc {
+ compatible = "regulator-fixed";
+ regulator-name = "vref-adc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&adc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_adc1>;
+ num-channels = <3>;
+ vref-supply = <®_vref_adc>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+
+ eeprom@0 {
+ compatible = "anvo,anv32e61w", "atmel,at25";
+ reg = <0>;
+ spi-max-frequency = <20000000>;
+ spi-cpha;
+ spi-cpol;
+ pagesize = <1>;
+ size = <8192>;
+ address-width = <16>;
+ };
+};
+
+&fec1 {
+ pinctrl-0 = <&pinctrl_enet1>;
+ /delete-node/ mdio;
+};
+
+&fec2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy2>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ micrel,led-mode = <0>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+
+ ethphy2: ethernet-phy@2 {
+ reg = <2>;
+ micrel,led-mode = <0>;
+ clocks = <&clks IMX6UL_CLK_ENET2_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&i2c1 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+};
+
+&i2c4 {
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ rtc@32 {
+ compatible = "epson,rx8900";
+ reg = <0x32>;
+ };
+};
+
+&pwm8 {
+ #pwm-cells = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm8>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ linux,rs485-enabled-at-boot-time;
+ rs485-rx-during-tx;
+ rs485-rts-active-low;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbotg1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg1>;
+ dr_mode = "otg";
+ srp-disable;
+ hnp-disable;
+ adp-disable;
+ over-current-active-low;
+ vbus-supply = <®_usb_otg1_vbus>;
+ status = "okay";
+};
+
+&usbotg2 {
+ dr_mode = "host";
+ disable-over-current;
+ vbus-supply = <®_5v>;
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <®_3v3>;
+ voltage-ranges = <3300 3300>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default", "state_100mhz", "state_200mhz";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
+ pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
+ non-removable;
+ keep-power-in-suspend;
+ wakeup-source;
+ vmmc-supply = <®_3v3>;
+ voltage-ranges = <3300 3300>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
+
+ pinctrl_adc1: adc1grp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
+ MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
+ MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1
+ MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1
+ MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1
+ MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */
+ >;
+ };
+
+ pinctrl_enet2: enet2grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009
+ >;
+ };
+
+ pinctrl_enet2_mdio: enet2mdiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp{
+ fsl,pins = <
+ MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
+ MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
+ >;
+ };
+
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */
+ MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */
+ MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */
+ MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */
+ >;
+ };
+
+ pinctrl_gpio_leds: gpioledsgrp {
+ fsl,pins = <
+ MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */
+ MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */
+ MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0
+ MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0
+ MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0
+ >;
+ };
+
+ pinctrl_pwm8: pwm8grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1
+ MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1
+ MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1
+ /*
+ * mux unused RTS to make sure it doesn't cause
+ * any interrupts when it is undefined
+ */
+ MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1
+ MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1
+ MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1
+ MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg1: usbotg1 {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0
+ >;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
+ MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
+ MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
+ MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
+ MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
+ MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
+ MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
+ >;
+ };
+
+ pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9
+ >;
+ };
+
+ pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
+ MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
+ MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
+ MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
+ MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
+ MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include "imx6ul-kontron-bl-common-u-boot.dtsi"
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+/dts-v1/;
+
+#include "imx6ul-kontron-sl.dtsi"
+#include "imx6ul-kontron-bl-common.dtsi"
+
+/ {
+ model = "Kontron BL i.MX6UL (N631X S)";
+ compatible = "kontron,bl-imx6ul", "kontron,sl-imx6ul", "fsl,imx6ul";
+};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0 OR MIT
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-#include "imx6ul-kontron-n6x1x-s-u-boot.dtsi"
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-/dts-v1/;
-
-#include "imx6ul-kontron-n631x-som.dtsi"
-#include "imx6ul-kontron-n6x1x-s.dtsi"
-
-/ {
- model = "Kontron N631X S";
- compatible = "kontron,imx6ul-n631x-s", "kontron,imx6ul-n631x-som",
- "fsl,imx6ul";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-#include "imx6ul.dtsi"
-#include "imx6ul-kontron-n6x1x-som-common.dtsi"
-
-/ {
- model = "Kontron N631X SOM";
- compatible = "kontron,imx6ul-n631x-som", "fsl,imx6ul";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0 OR MIT
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-#if defined(CONFIG_FIT)
-
-/ {
- binman: binman {
- filename = "flash.bin";
- pad-byte = <0x00>;
-
- spl: blob-ext@1 {
- offset = <0x0>;
- filename = "SPL";
- };
-
- uboot: blob-ext@2 {
- offset = <0x11000>;
- filename = "u-boot.img";
- };
- };
-};
-
-#endif /* CONFIG_FIT */
-
-/*
- * To make the PHYs work, we need to set the reset pin once. Afterwards
- * in Linux we can't assign the shared reset GPIO to the PHYs, as this
- * would cause Linux to reset both PHYs every time one of them gets
- * reinitialized.
- *
- * Also we disable the second ethernet as it currently doesn't work with
- * the devicetree setup in U-Boot.
- */
-
-&fec1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
- phy-mode = "rmii";
- phy-handle = <ðphy1>;
- phy-reset-gpios = <&gpio5 9 GPIO_ACTIVE_HIGH>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy1: ethernet-phy@1 {
- reg = <1>;
- micrel,led-mode = <0>;
- clocks = <&clks IMX6UL_CLK_ENET_REF>;
- clock-names = "rmii-ref";
- };
- };
-};
-
-&fec2 {
- status = "disabled";
- /delete-property/ phy-handle;
- /delete-node/ mdio;
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-/dts-v1/;
-
-#include <dt-bindings/gpio/gpio.h>
-#include "imx6ul-kontron-n6x1x-som.dtsi"
-
-/ {
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpio_leds>;
-
- led1 {
- label = "debug-led1";
- gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- default-state = "off";
- linux,default-trigger = "heartbeat";
- };
-
- led2 {
- label = "debug-led2";
- gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
- default-state = "off";
- };
-
- led3 {
- label = "debug-led3";
- gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
- default-state = "off";
- };
- };
-
- pwm-beeper {
- compatible = "pwm-beeper";
- pwms = <&pwm8 0 5000>;
- };
-
- reg_3v3: regulator-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- reg_5v: regulator-5v {
- compatible = "regulator-fixed";
- regulator-name = "5v";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- };
-
- reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
- compatible = "regulator-fixed";
- regulator-name = "usb_otg1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- reg_vref_adc: regulator-vref-adc {
- compatible = "regulator-fixed";
- regulator-name = "vref-adc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-};
-
-&adc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_adc1>;
- num-channels = <3>;
- vref-supply = <®_vref_adc>;
- status = "okay";
-};
-
-&can2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_flexcan2>;
- status = "okay";
-};
-
-&ecspi1 {
- cs-gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- eeprom@0 {
- compatible = "anvo,anv32e61w", "atmel,at25";
- reg = <0>;
- spi-max-frequency = <20000000>;
- spi-cpha;
- spi-cpol;
- pagesize = <1>;
- size = <8192>;
- address-width = <16>;
- };
-};
-
-&fec1 {
- pinctrl-0 = <&pinctrl_enet1>;
- /delete-node/ mdio;
-};
-
-&fec2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>;
- phy-mode = "rmii";
- phy-handle = <ðphy2>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy1: ethernet-phy@1 {
- reg = <1>;
- micrel,led-mode = <0>;
- clocks = <&clks IMX6UL_CLK_ENET_REF>;
- clock-names = "rmii-ref";
- };
-
- ethphy2: ethernet-phy@2 {
- reg = <2>;
- micrel,led-mode = <0>;
- clocks = <&clks IMX6UL_CLK_ENET2_REF>;
- clock-names = "rmii-ref";
- };
- };
-};
-
-&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-};
-
-&i2c4 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c4>;
- status = "okay";
-
- rtc@32 {
- compatible = "epson,rx8900";
- reg = <0x32>;
- };
-};
-
-&pwm8 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm8>;
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- linux,rs485-enabled-at-boot-time;
- rs485-rx-during-tx;
- rs485-rts-active-low;
- uart-has-rtscts;
- status = "okay";
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- fsl,uart-has-rtscts;
- status = "okay";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart4>;
- status = "okay";
-};
-
-&usbotg1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg1>;
- dr_mode = "otg";
- srp-disable;
- hnp-disable;
- adp-disable;
- over-current-active-low;
- vbus-supply = <®_usb_otg1_vbus>;
- status = "okay";
-};
-
-&usbotg2 {
- dr_mode = "host";
- disable-over-current;
- vbus-supply = <®_5v>;
- status = "okay";
-};
-
-&usdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1>;
- cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
- keep-power-in-suspend;
- wakeup-source;
- vmmc-supply = <®_3v3>;
- voltage-ranges = <3300 3300>;
- bus-width = <4>;
- no-1-8-v;
- status = "okay";
-};
-
-&usdhc2 {
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc2>;
- pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
- pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
- non-removable;
- keep-power-in-suspend;
- wakeup-source;
- vmmc-supply = <®_3v3>;
- voltage-ranges = <3300 3300>;
- bus-width = <4>;
- no-1-8-v;
- status = "okay";
-};
-
-&wdog1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wdog>;
- fsl,ext-reset-output;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
-
- pinctrl_adc1: adc1grp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
- MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
- MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1
- MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1
- MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1
- MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */
- >;
- };
-
- pinctrl_enet2: enet2grp {
- fsl,pins = <
- MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
- MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
- MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
- MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
- MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
- MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
- MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
- MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009
- >;
- };
-
- pinctrl_enet2_mdio: enet2mdiogrp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
- MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
- >;
- };
-
- pinctrl_flexcan2: flexcan2grp{
- fsl,pins = <
- MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
- MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
- >;
- };
-
- pinctrl_gpio: gpiogrp {
- fsl,pins = <
- MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */
- MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */
- MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */
- MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */
- >;
- };
-
- pinctrl_gpio_leds: gpioledsgrp {
- fsl,pins = <
- MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */
- MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */
- MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0
- MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0
- >;
- };
-
- pinctrl_i2c4: i2c4grp {
- fsl,pins = <
- MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0
- MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0
- >;
- };
-
- pinctrl_pwm8: pwm8grp {
- fsl,pins = <
- MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0
- >;
- };
-
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
- MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
- >;
- };
-
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1
- MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1
- MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1
- /*
- * mux unused RTS to make sure it doesn't cause
- * any interrupts when it is undefined
- */
- MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1
- >;
- };
-
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
- MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1
- MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1
- MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1
- >;
- };
-
- pinctrl_uart4: uart4grp {
- fsl,pins = <
- MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1
- MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1
- >;
- };
-
- pinctrl_usbotg1: usbotg1 {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
- MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
- MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
- MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
- MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
- MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
- MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059
- MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
- MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
- MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
- MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
- MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
- >;
- };
-
- pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
- fsl,pins = <
- MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9
- MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9
- MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9
- MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9
- MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9
- MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9
- >;
- };
-
- pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
- fsl,pins = <
- MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
- MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
- MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
- MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
- MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
- MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
- >;
- };
-
- pinctrl_wdog: wdoggrp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x30b0
- >;
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- gpio-leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpio_leds>;
-
- led1 {
- label = "debug-led1";
- gpios = <&gpio1 30 GPIO_ACTIVE_LOW>;
- default-state = "off";
- linux,default-trigger = "heartbeat";
- };
-
- led2 {
- label = "debug-led2";
- gpios = <&gpio5 3 GPIO_ACTIVE_LOW>;
- default-state = "off";
- };
-
- led3 {
- label = "debug-led3";
- gpios = <&gpio5 2 GPIO_ACTIVE_LOW>;
- default-state = "off";
- };
- };
-
- pwm-beeper {
- compatible = "pwm-beeper";
- pwms = <&pwm8 0 5000>;
- };
-
- reg_3v3: regulator-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-
- reg_5v: regulator-5v {
- compatible = "regulator-fixed";
- regulator-name = "5v";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- };
-
- reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
- compatible = "regulator-fixed";
- regulator-name = "usb_otg1_vbus";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- gpio = <&gpio1 4 GPIO_ACTIVE_HIGH>;
- enable-active-high;
- };
-
- reg_vref_adc: regulator-vref-adc {
- compatible = "regulator-fixed";
- regulator-name = "vref-adc";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- };
-};
-
-&adc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_adc1>;
- num-channels = <3>;
- vref-supply = <®_vref_adc>;
- status = "okay";
-};
-
-&can2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_flexcan2>;
- status = "okay";
-};
-
-&ecspi1 {
- cs-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi1>;
- status = "okay";
-
- eeprom@0 {
- compatible = "anvo,anv32e61w", "atmel,at25";
- reg = <0>;
- spi-max-frequency = <20000000>;
- spi-cpha;
- spi-cpol;
- pagesize = <1>;
- size = <8192>;
- address-width = <16>;
- };
-};
-
-&fec1 {
- pinctrl-0 = <&pinctrl_enet1>;
- /delete-node/ mdio;
-};
-
-&fec2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet2 &pinctrl_enet2_mdio>;
- phy-mode = "rmii";
- phy-handle = <ðphy2>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy1: ethernet-phy@1 {
- reg = <1>;
- micrel,led-mode = <0>;
- clocks = <&clks IMX6UL_CLK_ENET_REF>;
- clock-names = "rmii-ref";
- };
-
- ethphy2: ethernet-phy@2 {
- reg = <2>;
- micrel,led-mode = <0>;
- clocks = <&clks IMX6UL_CLK_ENET2_REF>;
- clock-names = "rmii-ref";
- };
- };
-};
-
-&i2c1 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c1>;
- status = "okay";
-};
-
-&i2c4 {
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_i2c4>;
- status = "okay";
-
- rtc@32 {
- compatible = "epson,rx8900";
- reg = <0x32>;
- };
-};
-
-&pwm8 {
- #pwm-cells = <2>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pwm8>;
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart1>;
- status = "okay";
-};
-
-&uart2 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart2>;
- linux,rs485-enabled-at-boot-time;
- rs485-rx-during-tx;
- rs485-rts-active-low;
- uart-has-rtscts;
- status = "okay";
-};
-
-&uart3 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart3>;
- uart-has-rtscts;
- status = "okay";
-};
-
-&uart4 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_uart4>;
- status = "okay";
-};
-
-&usbotg1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usbotg1>;
- dr_mode = "otg";
- srp-disable;
- hnp-disable;
- adp-disable;
- over-current-active-low;
- vbus-supply = <®_usb_otg1_vbus>;
- status = "okay";
-};
-
-&usbotg2 {
- dr_mode = "host";
- disable-over-current;
- vbus-supply = <®_5v>;
- status = "okay";
-};
-
-&usdhc1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_usdhc1>;
- cd-gpios = <&gpio1 19 GPIO_ACTIVE_LOW>;
- keep-power-in-suspend;
- wakeup-source;
- vmmc-supply = <®_3v3>;
- voltage-ranges = <3300 3300>;
- no-1-8-v;
- status = "okay";
-};
-
-&usdhc2 {
- pinctrl-names = "default", "state_100mhz", "state_200mhz";
- pinctrl-0 = <&pinctrl_usdhc2>;
- pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
- pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
- non-removable;
- keep-power-in-suspend;
- wakeup-source;
- vmmc-supply = <®_3v3>;
- voltage-ranges = <3300 3300>;
- no-1-8-v;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl-0 = <&pinctrl_reset_out &pinctrl_gpio>;
-
- pinctrl_adc1: adc1grp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO02__GPIO1_IO02 0xb0
- MX6UL_PAD_GPIO1_IO03__GPIO1_IO03 0xb0
- MX6UL_PAD_GPIO1_IO08__GPIO1_IO08 0xb0
- >;
- };
-
- pinctrl_ecspi1: ecspi1grp {
- fsl,pins = <
- MX6UL_PAD_CSI_DATA07__ECSPI1_MISO 0x100b1
- MX6UL_PAD_CSI_DATA06__ECSPI1_MOSI 0x100b1
- MX6UL_PAD_CSI_DATA04__ECSPI1_SCLK 0x100b1
- MX6UL_PAD_CSI_DATA05__GPIO4_IO26 0x100b1 /* ECSPI1-CS1 */
- >;
- };
-
- pinctrl_enet2: enet2grp {
- fsl,pins = <
- MX6UL_PAD_ENET2_RX_EN__ENET2_RX_EN 0x1b0b0
- MX6UL_PAD_ENET2_RX_ER__ENET2_RX_ER 0x1b0b0
- MX6UL_PAD_ENET2_RX_DATA0__ENET2_RDATA00 0x1b0b0
- MX6UL_PAD_ENET2_RX_DATA1__ENET2_RDATA01 0x1b0b0
- MX6UL_PAD_ENET2_TX_EN__ENET2_TX_EN 0x1b0b0
- MX6UL_PAD_ENET2_TX_DATA0__ENET2_TDATA00 0x1b0b0
- MX6UL_PAD_ENET2_TX_DATA1__ENET2_TDATA01 0x1b0b0
- MX6UL_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 0x4001b009
- >;
- };
-
- pinctrl_enet2_mdio: enet2mdiogrp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO07__ENET2_MDC 0x1b0b0
- MX6UL_PAD_GPIO1_IO06__ENET2_MDIO 0x1b0b0
- >;
- };
-
- pinctrl_flexcan2: flexcan2grp{
- fsl,pins = <
- MX6UL_PAD_UART2_RTS_B__FLEXCAN2_RX 0x1b020
- MX6UL_PAD_UART2_CTS_B__FLEXCAN2_TX 0x1b020
- >;
- };
-
- pinctrl_gpio: gpiogrp {
- fsl,pins = <
- MX6UL_PAD_SNVS_TAMPER5__GPIO5_IO05 0x1b0b0 /* DOUT1 */
- MX6UL_PAD_SNVS_TAMPER4__GPIO5_IO04 0x1b0b0 /* DIN1 */
- MX6UL_PAD_SNVS_TAMPER1__GPIO5_IO01 0x1b0b0 /* DOUT2 */
- MX6UL_PAD_SNVS_TAMPER0__GPIO5_IO00 0x1b0b0 /* DIN2 */
- >;
- };
-
- pinctrl_gpio_leds: gpioledsgrp {
- fsl,pins = <
- MX6UL_PAD_UART5_TX_DATA__GPIO1_IO30 0x1b0b0 /* LED H14 */
- MX6UL_PAD_SNVS_TAMPER3__GPIO5_IO03 0x1b0b0 /* LED H15 */
- MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02 0x1b0b0 /* LED H16 */
- >;
- };
-
- pinctrl_i2c1: i2c1grp {
- fsl,pins = <
- MX6UL_PAD_CSI_PIXCLK__I2C1_SCL 0x4001b8b0
- MX6UL_PAD_CSI_MCLK__I2C1_SDA 0x4001b8b0
- >;
- };
-
- pinctrl_i2c4: i2c4grp {
- fsl,pins = <
- MX6UL_PAD_UART2_TX_DATA__I2C4_SCL 0x4001f8b0
- MX6UL_PAD_UART2_RX_DATA__I2C4_SDA 0x4001f8b0
- >;
- };
-
- pinctrl_pwm8: pwm8grp {
- fsl,pins = <
- MX6UL_PAD_CSI_HSYNC__PWM8_OUT 0x110b0
- >;
- };
-
- pinctrl_uart1: uart1grp {
- fsl,pins = <
- MX6UL_PAD_UART1_TX_DATA__UART1_DCE_TX 0x1b0b1
- MX6UL_PAD_UART1_RX_DATA__UART1_DCE_RX 0x1b0b1
- >;
- };
-
- pinctrl_uart2: uart2grp {
- fsl,pins = <
- MX6UL_PAD_NAND_DATA04__UART2_DCE_TX 0x1b0b1
- MX6UL_PAD_NAND_DATA05__UART2_DCE_RX 0x1b0b1
- MX6UL_PAD_NAND_DATA06__UART2_DCE_CTS 0x1b0b1
- /*
- * mux unused RTS to make sure it doesn't cause
- * any interrupts when it is undefined
- */
- MX6UL_PAD_NAND_DATA07__UART2_DCE_RTS 0x1b0b1
- >;
- };
-
- pinctrl_uart3: uart3grp {
- fsl,pins = <
- MX6UL_PAD_UART3_TX_DATA__UART3_DCE_TX 0x1b0b1
- MX6UL_PAD_UART3_RX_DATA__UART3_DCE_RX 0x1b0b1
- MX6UL_PAD_UART3_CTS_B__UART3_DCE_CTS 0x1b0b1
- MX6UL_PAD_UART3_RTS_B__UART3_DCE_RTS 0x1b0b1
- >;
- };
-
- pinctrl_uart4: uart4grp {
- fsl,pins = <
- MX6UL_PAD_UART4_TX_DATA__UART4_DCE_TX 0x1b0b1
- MX6UL_PAD_UART4_RX_DATA__UART4_DCE_RX 0x1b0b1
- >;
- };
-
- pinctrl_usbotg1: usbotg1 {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO04__GPIO1_IO04 0x1b0b0
- >;
- };
-
- pinctrl_usdhc1: usdhc1grp {
- fsl,pins = <
- MX6UL_PAD_SD1_CMD__USDHC1_CMD 0x17059
- MX6UL_PAD_SD1_CLK__USDHC1_CLK 0x10059
- MX6UL_PAD_SD1_DATA0__USDHC1_DATA0 0x17059
- MX6UL_PAD_SD1_DATA1__USDHC1_DATA1 0x17059
- MX6UL_PAD_SD1_DATA2__USDHC1_DATA2 0x17059
- MX6UL_PAD_SD1_DATA3__USDHC1_DATA3 0x17059
- MX6UL_PAD_UART1_RTS_B__GPIO1_IO19 0x100b1 /* SD1_CD */
- >;
- };
-
- pinctrl_usdhc2: usdhc2grp {
- fsl,pins = <
- MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x10059
- MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x17059
- MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x17059
- MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x17059
- MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x17059
- MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x17059
- >;
- };
-
- pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp {
- fsl,pins = <
- MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100b9
- MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170b9
- MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170b9
- MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170b9
- MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170b9
- MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170b9
- >;
- };
-
- pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp {
- fsl,pins = <
- MX6UL_PAD_NAND_RE_B__USDHC2_CLK 0x100f9
- MX6UL_PAD_NAND_WE_B__USDHC2_CMD 0x170f9
- MX6UL_PAD_NAND_DATA00__USDHC2_DATA0 0x170f9
- MX6UL_PAD_NAND_DATA01__USDHC2_DATA1 0x170f9
- MX6UL_PAD_NAND_DATA02__USDHC2_DATA2 0x170f9
- MX6UL_PAD_NAND_DATA03__USDHC2_DATA3 0x170f9
- >;
- };
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
- */
-
-#include <dt-bindings/gpio/gpio.h>
-
-/ {
- chosen {
- stdout-path = &uart4;
- };
-};
-
-&ecspi2 {
- cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_ecspi2>;
- status = "okay";
-
- flash@0 {
- compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
- spi-max-frequency = <50000000>;
- reg = <0>;
- };
-};
-
-&fec1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
- phy-mode = "rmii";
- phy-handle = <ðphy1>;
- status = "okay";
-
- mdio {
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy1: ethernet-phy@1 {
- reg = <1>;
- micrel,led-mode = <0>;
- clocks = <&clks IMX6UL_CLK_ENET_REF>;
- clock-names = "rmii-ref";
- };
- };
-};
-
-&fec2 {
- phy-mode = "rmii";
- status = "disabled";
-};
-
-&qspi {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_qspi>;
- status = "okay";
-};
-
-&wdog1 {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_wdog>;
- fsl,ext-reset-output;
- status = "okay";
-};
-
-&iomuxc {
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_reset_out>;
-
- pinctrl_ecspi2: ecspi2grp {
- fsl,pins = <
- MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x100b1
- MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x100b1
- MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x100b1
- MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x100b1
- >;
- };
-
- pinctrl_enet1: enet1grp {
- fsl,pins = <
- MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
- MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
- MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
- MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
- MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
- MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
- MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
- MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b009
- >;
- };
-
- pinctrl_enet1_mdio: enet1mdiogrp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
- MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
- >;
- };
-
- pinctrl_qspi: qspigrp {
- fsl,pins = <
- MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1
- MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1
- MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1
- MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1
- MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1
- MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
- >;
- };
-
- pinctrl_reset_out: rstoutgrp {
- fsl,pins = <
- MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x1b0b0
- >;
- };
-
- pinctrl_wdog: wdoggrp {
- fsl,pins = <
- MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x18b0
- >;
- };
-};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ memory@80000000 {
+ reg = <0x80000000 0x10000000>;
+ device_type = "memory";
+ };
+};
+
+&ecspi2 {
+ cs-gpios = <&gpio4 22 GPIO_ACTIVE_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+
+ flash@0 {
+ compatible = "mxicy,mx25v8035f", "jedec,spi-nor";
+ spi-max-frequency = <50000000>;
+ reg = <0>;
+ };
+};
+
+&fec1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet1 &pinctrl_enet1_mdio>;
+ phy-mode = "rmii";
+ phy-handle = <ðphy1>;
+ status = "okay";
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ micrel,led-mode = <0>;
+ clocks = <&clks IMX6UL_CLK_ENET_REF>;
+ clock-names = "rmii-ref";
+ };
+ };
+};
+
+&fec2 {
+ phy-mode = "rmii";
+ status = "disabled";
+};
+
+&qspi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_qspi>;
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "spi-nand";
+ spi-max-frequency = <104000000>;
+ spi-tx-bus-width = <4>;
+ spi-rx-bus-width = <4>;
+ reg = <0>;
+ };
+};
+
+&wdog1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_wdog>;
+ fsl,ext-reset-output;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_reset_out>;
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6UL_PAD_CSI_DATA03__ECSPI2_MISO 0x100b1
+ MX6UL_PAD_CSI_DATA02__ECSPI2_MOSI 0x100b1
+ MX6UL_PAD_CSI_DATA00__ECSPI2_SCLK 0x100b1
+ MX6UL_PAD_CSI_DATA01__GPIO4_IO22 0x100b1
+ >;
+ };
+
+ pinctrl_enet1: enet1grp {
+ fsl,pins = <
+ MX6UL_PAD_ENET1_RX_EN__ENET1_RX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_RX_ER__ENET1_RX_ER 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA0__ENET1_RDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_RX_DATA1__ENET1_RDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_EN__ENET1_TX_EN 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA0__ENET1_TDATA00 0x1b0b0
+ MX6UL_PAD_ENET1_TX_DATA1__ENET1_TDATA01 0x1b0b0
+ MX6UL_PAD_ENET1_TX_CLK__ENET1_REF_CLK1 0x4001b009
+ >;
+ };
+
+ pinctrl_enet1_mdio: enet1mdiogrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO07__ENET1_MDC 0x1b0b0
+ MX6UL_PAD_GPIO1_IO06__ENET1_MDIO 0x1b0b0
+ >;
+ };
+
+ pinctrl_qspi: qspigrp {
+ fsl,pins = <
+ MX6UL_PAD_NAND_WP_B__QSPI_A_SCLK 0x70a1
+ MX6UL_PAD_NAND_READY_B__QSPI_A_DATA00 0x70a1
+ MX6UL_PAD_NAND_CE0_B__QSPI_A_DATA01 0x70a1
+ MX6UL_PAD_NAND_CE1_B__QSPI_A_DATA02 0x70a1
+ MX6UL_PAD_NAND_CLE__QSPI_A_DATA03 0x70a1
+ MX6UL_PAD_NAND_DQS__QSPI_A_SS0_B 0x70a1
+ >;
+ };
+
+ pinctrl_reset_out: rstoutgrp {
+ fsl,pins = <
+ MX6UL_PAD_SNVS_TAMPER9__GPIO5_IO09 0x1b0b0
+ >;
+ };
+
+ pinctrl_wdog: wdoggrp {
+ fsl,pins = <
+ MX6UL_PAD_GPIO1_IO09__WDOG1_WDOG_ANY 0x18b0
+ >;
+ };
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ * Copyright (c) 2019 Krzysztof Kozlowski <krzk@kernel.org>
+ */
+
+#include "imx6ul.dtsi"
+#include "imx6ul-kontron-sl-common.dtsi"
+
+/ {
+ model = "Kontron SL i.MX6UL (N631X SOM)";
+ compatible = "kontron,sl-imx6ul", "fsl,imx6ul";
+};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0 OR MIT
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include "imx6ul-kontron-bl-common-u-boot.dtsi"
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2019 Kontron Electronics GmbH
+ */
+
+/dts-v1/;
+
+#include "imx6ull-kontron-sl.dtsi"
+#include "imx6ul-kontron-bl-common.dtsi"
+
+/ {
+ model = "Kontron BL i.MX6ULL (N641X S)";
+ compatible = "kontron,bl-imx6ull", "kontron,sl-imx6ull", "fsl,imx6ull";
+};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0 OR MIT
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-#include "imx6ul-kontron-n6x1x-s-u-boot.dtsi"
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2019 Kontron Electronics GmbH
- */
-
-/dts-v1/;
-
-#include "imx6ull-kontron-n641x-som.dtsi"
-#include "imx6ul-kontron-n6x1x-s.dtsi"
-
-/ {
- model = "Kontron N641X S";
- compatible = "kontron,imx6ull-n641x-s", "kontron,imx6ull-n641x-som",
- "fsl,imx6ull";
-};
+++ /dev/null
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Copyright (C) 2017 exceet electronics GmbH
- * Copyright (C) 2018 Kontron Electronics GmbH
- */
-
-#include "imx6ull.dtsi"
-#include "imx6ul-kontron-n6x1x-som-common.dtsi"
-
-/ {
- model = "Kontron N641X SOM";
- compatible = "kontron,imx6ull-n641x-som", "fsl,imx6ull";
-};
--- /dev/null
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2017 exceet electronics GmbH
+ * Copyright (C) 2018 Kontron Electronics GmbH
+ */
+
+#include "imx6ull.dtsi"
+#include "imx6ul-kontron-sl-common.dtsi"
+
+/ {
+ model = "Kontron SL i.MX6ULL (N641X SOM)";
+ compatible = "kontron,sl-imx6ull", "fsl,imx6ull";
+};
Kontron SL/BL i.MX6UL/ULL Boards (N63xx/N64xx)
M: Frieder Schrempf <frieder.schrempf@kontron.de>
S: Maintained
-F: arch/arm/dts/imx6ul-kontron-n6*
-F: arch/arm/dts/imx6ull-kontron-n6*
+F: arch/arm/dts/imx6ul-kontron-sl*
+F: arch/arm/dts/imx6ul-kontron-bl*
+F: arch/arm/dts/imx6ull-kontron-sl*
+F: arch/arm/dts/imx6ull-kontron-bl*
F: board/kontron/sl-mx6ul
F: configs/kontron-sl-mx6ul_defconfig
F: doc/board/kontron/sl-mx6ul.rst
DECLARE_GLOBAL_DATA_PTR;
enum {
- BOARD_TYPE_KTN_N631X = 1,
- BOARD_TYPE_KTN_N641X,
+ BOARD_TYPE_KTN_SL_UL = 1,
+ BOARD_TYPE_KTN_SL_ULL,
BOARD_TYPE_MAX
};
static int do_board_detect(void)
{
if (is_mx6ul())
- gd->board_type = BOARD_TYPE_KTN_N631X;
+ gd->board_type = BOARD_TYPE_KTN_SL_UL;
else if (is_mx6ull())
- gd->board_type = BOARD_TYPE_KTN_N641X;
+ gd->board_type = BOARD_TYPE_KTN_SL_ULL;
printf("Kontron SL i.MX6UL%s (N6%s1x) module, %lu MB RAM detected\n",
is_mx6ull() ? "L" : "", is_mx6ull() ? "4" : "3", gd->ram_size / SZ_1M);
int board_fit_config_name_match(const char *name)
{
- if (gd->board_type == BOARD_TYPE_KTN_N631X && is_mx6ul() &&
- !strcmp(name, "imx6ul-kontron-n631x-s"))
+ if (gd->board_type == BOARD_TYPE_KTN_SL_UL && is_mx6ul() &&
+ (!strcmp(name, "imx6ul-kontron-n631x-s") || !strcmp(name, "imx6ul-kontron-bl")))
return 0;
- if (gd->board_type == BOARD_TYPE_KTN_N641X && is_mx6ull() &&
- !strcmp(name, "imx6ull-kontron-n641x-s"))
+ if (gd->board_type == BOARD_TYPE_KTN_SL_ULL && is_mx6ull() &&
+ (!strcmp(name, "imx6ull-kontron-n641x-s") || !strcmp(name, "imx6ull-kontron-bl")))
return 0;
return -1;
CONFIG_MX6UL=y
CONFIG_TARGET_KONTRON_MX6UL=y
CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="imx6ul-kontron-n631x-s"
+CONFIG_DEFAULT_DEVICE_TREE="imx6ul-kontron-bl"
CONFIG_SPL_TEXT_BASE=0x00908000
CONFIG_SPL_MMC=y
CONFIG_SPL_SERIAL=y
CONFIG_CMD_UBI=y
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
-CONFIG_OF_LIST="imx6ul-kontron-n631x-s imx6ull-kontron-n641x-s"
+CONFIG_OF_LIST="imx6ul-kontron-bl imx6ull-kontron-bl"
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_MMC=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
projects / uboot.git / commitdiff