arm64: dts: hikey: Fix eMMC corruption regression

arm64: dts: hikey: Fix eMMC corruption regression

This patch is a partial revert of
commit 148f8088d1b8 ("arm64: dts: hikey: Enable HS200 mode on eMMC")

which has been causing eMMC corruption on my HiKey board.

Symptoms usually looked like:

mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
...
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc0: new HS200 MMC card at address 0001
...
dwmmc_k3 f723d000.dwmmc0: Unexpected command timeout, state 3
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
print_req_error: I/O error, dev mmcblk0, sector 8810504
Aborting journal on device mmcblk0p10-8.
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 24800000Hz (slot req 400000Hz, actual 400000HZ div = 31)
mmc_host mmc0: Bus speed (slot 0) = 148800000Hz (slot req 150000000Hz, actual 148800000HZ div = 0)
EXT4-fs error (device mmcblk0p10): ext4_journal_check_start:61: Detected aborted journal
EXT4-fs (mmcblk0p10): Remounting filesystem read-only

And quite often this would result in a disk that wouldn't properly
boot even with older kernels.

It seems the max-frequency property added by the above patch is
causing the problem, so remove it.

Cc: Ryan Grachek <ryan@edited.us>
Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: YongQin Liu <yongqin.liu@linaro.org>
Cc: Leo Yan <leo.yan@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Wei Xu <xuwei04@gmail.com>